Lavalier or shotgun mic for interview: types, connection and sync
What to plug where, what protects the lavalier microphone and where the noise in the recording comes from.
Lavalier or shotgun mic for interview — two different tasks that are solved together on set: to record the speech of the interviewee and to record it so that it does not depend on the distance to the camera. The connection scheme is simple: a lavalier microphone on the interviewee, a backup boom over the frame, both signals into one recorder, and a reference track is fed to the camera for the sync. Below are the types of microphones, how they are connected, how to get clean sound and where the noise on the recording comes from.
Types of microphones
Lavalier microphones differ in their polar pattern, and it decides how much unwanted sound gets into the recording. The Shure WL183 has an omnidirectional pattern, a pickup angle of 360°: the microphone hears everything around it, but it has a low level of noise from handling. The WL184 has a supercardioid pattern, a pickup angle of 115°: side sounds are cut off, and the manufacturer directly recommends using a windscreen. The WL185 has a cardioid pattern, a pickup angle of 130° — a compromise between the first two, and it needs a windscreen as well.
Beyond the lavaliers there is the broadcast class — shotgun microphones. The RØDE NTG5 is a broadcast-class shotgun microphone with a supercardioid pattern, a self noise of 10 dBA, a weight of 76 g and a length of 203 mm. The interference tube makes it much less sensitive to sound from the side and from behind. It is hard to aim one such microphone at two people at once, so in a live conversation the interviewees are recorded with separate microphones.
The stated specifications of the lavaliers are worth knowing in advance. The Shure WL18x family is electret condenser microphones for wireless transmitters with a common frequency response from 50 Hz to 17 000 Hz. The WL183 has a maximum sound pressure level of 125 dB SPL and a self noise of 22.5 dB SPL.
Connection and sync
The basic connection scheme for an interview: a lavalier microphone and a boom on each interviewee, everything into one recorder. The sound is recorded from all the sources, and a reference track is fed to the cameras — the editor later syncs the picture with the sound on it. In this scheme the boom is not a replacement for the lavalier, but an insurance: the rustle of clothing on one is covered by the other.
- Power: the lavalier needs +5 Vdc, the permissible range is 1.5–10 Vdc.
- Connector and cable: the 1.2 m cable ends in a TA4F connector and plugs into the transmitter.
- Mounting: from 76 mm to 152 mm below the collar cutout, on the outside of the clothing.
- Windscreen: the snap-fit gives 30 dB of protection from plosives, the foam one from 5 to 10 dB.
- Recording on the transmitter: 32-bit recording in floating point.
Wireless kits give a second layer of insurance. The DJI Mic 2 records 32-bit in floating point on the device, keeps up to 14 hours of internal recording, shoots at a distance of up to 250 m and works for up to 18 hours. The RØDE Wireless PRO does the same: 32-bit recording in floating point, a built-in timecode for sync in post, a range of up to 260 m, 32 GB of built-in memory per transmitter and more than 40 hours of recording.
How to record clean sound
The main rule is the distance to the source. When the distance is doubled, the sound pressure level reaching the microphone drops by a factor of four, and the speech becomes harder and harder to make out. That is why the lavalier is fixed on the outside of the clothing, roughly 6 to 8 inches below the chin: the distance to the mouth stays constant, and the level does not wander from take to take.
A shotgun microphone on a boom is placed just outside the frame — so the speech is heard and the microphone itself does not get into the picture. But it is hard to aim one shotgun at two people at once, so in a live conversation they are still recorded with separate microphones.
The insurance is built on a second microphone: the boom records the speech in parallel with the lavalier, and if the lavalier picked up the rustle of clothing, the editor is left with a second recording. For lavaliers with a directional pattern a windscreen is obligatory — that is a direct requirement of the manufacturer for the WL184 and WL185.
Noise and its causes
Noise on a recording always has a concrete cause, and every cause has its own solution.
- Plosives: keep the microphone no closer than 6 inches from the mouth, tilt it about 45 degrees from the vertical and put on the foam windscreen.
- Wind: outdoors a foam windscreen, in difficult cases a “zeppelin”; condenser microphones are especially sensitive to wind.
- Noise from the stand: a shock mount on the stand removes the noise that comes through the stand or the boom.
- Electrical hum: unbalanced cables next to lamps and dimmers cause it; the solution is balanced cables.
Handling and clothing deserve a separate mention. The WL183 has a low level of noise from handling, but the clothing next to the microphone stays a source of noise, which is exactly why the backup boom is needed in the connection scheme.
Frequently asked questions
Do you need a separate sound recordist?
A separate sound recordist is not necessary if the connection scheme is assembled in advance: a lavalier microphone and a boom on each interviewee, everything into one recorder, the sound is recorded from all the sources, and a reference track is fed to the cameras. Where a live conversation of two is recorded, one shotgun microphone on a boom is not enough — they are recorded with separate microphones.
What to do with the noise on set?
Noise is treated at the source. Plosives — the microphone no closer than 6 inches from the mouth, a tilt of about 45 degrees from the vertical and a foam windscreen. Wind outdoors — a foam windscreen, in difficult cases a “zeppelin”, and condenser microphones are especially sensitive to wind. Noise from the stand is removed by a shock mount: it takes away what comes through the stand or the boom. Electrical hum is caused by unbalanced cables next to lamps and dimmers — balanced cables help. And the last thing: the lavalier is placed on the outside of the clothing, roughly 6 to 8 inches below the chin, and the backup boom covers the rustle of clothing that remained in the lavalier recording.
What to read next
Need this done as a project?
We take on projects like this — with the same settings we walk through in this piece.